Analisis Sifat Mekanik Komposit Serat Sabut Kelapa dengan Perlakuan Alkalisasi Etanol dan Filler Arang Tempurung Kelapa
Main Article Content
Abstract
Coconut trees are plants that are easily found in tropical areas such as Indonesia; therefore, natural products are abundant, but the use of waste from coconuts has not been processed into technological products. The aim of this study was to determine the differences in the variations in the volume fraction of fibers during tensile and impact strength testing. The variations in the volume fraction used were 5%, 10%, and 15% fiber, and the chemical treatment of the fiber was alkalized using 20% ethanol for 3 h of soaking. Composite manufacturing uses a hand layup method with random fiber orientation. The results of the research on variations in volume fraction of 5%, 10% and 15% obtained test values, in tensile testing such as maximum load obtained 32,844 kgf, 106.44 kgf and 105.59 kgf, maximum stress 6.0510 N/mm2, 16,893 N/ mm2 and 17.249 N/mm2, elongation breaking strain 0.8150, 0.3275 and 0.2617, breaking strain 1.4818 %, 0.5955 % and 0.4758 %, for the tensile test value the impact energy value was found to be 1.6 kgf, 2.3 kgf and 3.3 kgf and impact prices of 1.84 kJ/m2 , 2.45 kJ/m2 and 3.45 kJ/m2 . The high tensile and impact test results were due to mixing coconut fiber which had gone through ethanol alkalizing treatment with coconut charcoal powder to obtain high impact and tensile values.
Article Details
This work is licensed under a Creative Commons Attribution 4.0 International License.
References
T. Indahyani, “Pemanfaatan Limbah Sabut Kelapa pada Perencanaan Interior dan Furniture yang Berdampak pada Pemberdayaan Masyarakat Miskin,” Bina Nusant. Univ., no. Vol. 2 No. 1 (2011): Humaniora, pp. 15–23, 2011.
D. Wijaya and S. Hidayat, “Pengaruh Fraksi Volume Serat pada Komposit Hibrid Serat Tebu dan Serat Sabut Kelapa terhadap Kekuatan Tarik,” Pros. 13th Ind. Res. Work. Natl. Semin. Bandung, vol. 13, pp. 78–83, 2022.
A. Haryanti, N. Norsamsi, P. S. Fanny Sholiha, and N. P. Putri, “Studi Pemanfaatan Limbah Padat Kelapa Sawit,” Konversi, vol. 3, no. 2, p. 20, 2014.
M. Mirmanto, S. Sugiman, F. Fathurrahman, and M. D. Ramadhani, “Konduktivitas termal komposit resin epoksi dan serbuk arang tempurung kelapa,” Din. Tek. Mesin, vol. 12, no. 1, p. 29, 2022.
F. I. Sijabat, J. Saragih, and Halimatuddahliana, “Pengaruh Ukuran Serbuk Tempurung Kelapa Sebagai Pengisi Komposit Poliester Tak Jenuh Terhadap Sifat Mekanik Dan Penyerapan Air,” J. Tek. Kim. USU, vol. 2, no. 4, pp. 31– 37, 2013.
M. A. Pradana, H. Ardhyananta, and M. Farid, “Pemisahan Selulosa dari Lignin Serat Tandan Kosong Kelapa Sawit dengan Proses Alkalisasi untuk Penguat Bahan Komposit Penyerap Suara,” J. Tek. ITS, vol. 6, no. 2, pp. 413–416, 2017.
B. Maryanti, A. Sonief, “Pengaruh Alkalisasi Komposit Serat Kelapa- Poliester Terhadap Kekuatan Tarik,” Rekayasa Mesin, vol. 2, no. 2, pp. 123– 129, 2011.
R. C. L. Oroh, Jonathan. Frans P Sappu, “Analisis Sifat Mekanik Matrial Komposit Dari Serat Sabut Kelapa,” J. Polos Tek. Mesin Unsrat, vol. 1, 2013.
W. D. Callister Jr and D. G. Rethwisch, Structures and Properties of Ceramics. 2018.
R. H. Setyanto, “Review : Teknik Manufaktur Komposit Hijau dan Aplikasinya,” Performa, vol. 11, no. 1, pp. 9–18, 2012.
F. N. F. Rindrawan, “Karakteristik Kekuatan Komposit Serabut Kepala dengan Variasi Arah Serat,” Tek. mesin, vol. 3, no. 1, pp. 1–6, 2016.
T. W. Putra, F.G., Ngafwan., Riyadi, “Pengaruh Variasi Berat Filler Karbon Aktif Tempurung,” J. Tek. Mesin, vol. 1, no. 2, pp. 29–38, 2016.
A. Taka, F. Kristianta, and I. Sholahuddin, “Variasi Ukuran terhadap Kekerasan dan Laju Keausan Komposit Epoxy Alumunium-Serbuk Tempurung Kelapa untuk Kampas Rem,” J. Rekayasa Mesin, vol. 8, no. 3, pp. 149–153, 2017.
H. Wona, K. Boimau, and E. U. K. Maliwemu, “Pengaruh Variasi Fraksi Volume Serat terhadap Kekuatan Bending dan Impak Komposit Polyester Berpenguat Serat Agave Cantula,” Lontar J. Tek. Mesin, vol. 02, no. 01, pp. 39–50, 2015.