Analisis Perbaikan Pengendalian Kualitas Produk Pintu dengan Menggunakan Metode Six Sigma dan FMEA Pada PD. Indah Mulya
Main Article Content
Abstract
PD Indah Mulya is a trading company engaged in the wood processing industry, one of which is a door type product. In door production at PD Indah Mulya, there are usually defects such as splitting, sunken and porous. The defect needs to be corrected. The purpose of this study is to determine the percentage and factors that cause defects that most often occur and provide suggestions for quality improvement actions. The methods used are Six Sigma and Failure Mode Effect Analysis (FMEA) at the improve stage. Based on the results of the study, the percentage of product defects is 27% split, 42% concave defects and 30% porous defects. The type of defect that occurs a lot in PD Indah Mulya is a sunken defect. Sunken defects are usually caused by the type of wood used is young. Based on the results of RPN calculations for FMEA door production, several risks are obtained that have the highest priority level for making repairs to minimize the possibility of errors. Calculation The highest RPN value is 180 from the type of concave defect with the cause of inappropriate selection of raw materials. The recommendation for proposed improvements to overcome this problem is to conduct coaching for the raw material selection process.
Article Details
This work is licensed under a Creative Commons Attribution 4.0 International License.
References
F. Ahmad, “Six Sigma DMAIC Sebagai Metode Pengendalian Kualitas Produk Kursi Pada UKM,” JISI: Jurnal Integrasi Sistem Industri, vol. 6, no. 1, pp. 11–17, 2019.
I. Mashabai, Fikri, Jumriani, and T. Indrayani, “Analisis Pengendalian Kualitas Produk Pintu Rumah Pada UD Rahman Meubeler dengan Mengunakan Metode Six Sigma Desa Pungka Kab Sumbawa Besar,” JITSA: Jurnal Industri&Teknologi Samawa, vol. 3, no. 1, pp. 49–53, 2022.
H. Ramadhani and I. N. Gusniar, “Usulan Penerapan Metode Lean Six Sigma untuk Menurunkan Angka Produk Cacat pada Produksi Camshaft di PT. Morita Tjokro Gearindo,” JSE: Serambi Engineering, vol. 8, no. 1, pp. 4572–4580, 2023.
M. A. Faiz, Winarno, and A. Suseno, “Analisis Pengendalian Kualitas Produk Celana pada UMKM KMStoreid Menggunakan Metode Statistical Process Control,” Jurnal Serambi Engineering, vol. 6, no. 4, pp. 4015–4023, 2022.
P. S. K. Hanifah and I. Iftadi, “Penerapan Metode Six Sigma dan Failure Mode Effect Analysis untuk Perbaikan Pengendalian Kualitas Produksi Gula,” Jurnal INTECH Teknik Industri Universitas Serang Raya, vol. 8, no. 2, pp. 90–98, 2022.
A. Rahman and S. Perdana, “Analisis Perbaikan Kualitas Produk Carton Box di PT XYZ Dengan Metode DMAIC dan FMEA,” Jurnal Optimasi Teknik Industri, vol. 3, no. 1, pp. 33–37, 2021.
H. Dewi, Maryam, and D. Sutiyarno, “Analisa produk cacat menggunakan metode peta kendali p dan root cause analysis,” Jurnal Teknologi Pertanian, vol. 7, no. 2, pp. 10–18, 2018.
A. Khatammi and A. W. Rizqi, “Analisis Kecacatan Produk Pada Hasil Pengelasan dengan Metode Failure Mode Effect Analysis,” Jurnal Serambi Engineering, vol. 7, no. 2, pp. 2922–2928, 2022.
D. Z. Wati and P. W. Laksono, “Metode Six Sigma sebagai Solusi Peningkatan dan Pengendalian Kualitas Proses Produksi KKBW 480 di PT INKA Persero,” in Seminar dan Konferensi Nasional IDEC 2022, 2022, pp. 1–11.
G. A. Wibowo and A. Z. Al Faristy, “Penerapan Six Sigma Dalam Pengendalian Kualitas Produk Mebel Pada PT Alis Jaya Ciptatama,” Jurnal Teknik Mesin, Industri, Elektro, dan Informatika (JTMEI), vol. 2, no. 3, pp. 203–211, 2023.
E. Riandari, J. Susetyo, and E. W. Asih, “Pengendalian Kualitas Produksi Genteng Menggunakan Penerapan Metode Six Sigma dan Failure Mode and Effect Analysis (FMEA),” Jurnal REKAVASI: Jurnal Rekayasa dan Inovasi Teknik Industri, vol. 10, no. 1, pp. 64–71, 2022.
A. Suherman and B. J. Cahyana, “Pengendalian Kualitas Dengan Metode Failure Mode Effect and Analysis (FMEA) Dan Pendekatan Kaizen untuk Mengurangi Jumlah Kecacatan dan Penyebabnya,” in Prosiding Semnastek, 2019, pp. 1–9.
B. Septiana and B. Purwanggono, “Analisis Pengendalian Kualitas dengan Menggunakan Failure Mode Error Analysis (FMEA) Pada Divisi Sewing PT Pisma Garment Indo,” Industrial Engineering Online Journal, vol. 7, no. 3, 2018.
A. Y. Setiawan, J. Susetyo, and R. A. Simanjuntak, “Pengendalian Kualitas Produk Menggunakan Metode Six Sigma dan Failure Mode and Effect Analysis (FMEA) Pada PT. Papertech Indonesia Unit II Magelang,” Jurnal REKAVASI: Jurnal Rekayasa dan Inovasi Teknik Industri, vol. 9, no. 1, pp. 9–19, 2021.
A. Qothrunnada and Rochmoeljati, “Pengendalian Kualitas Proses Produksi Paving Block K300 T-6 Dengan Menggunakan Metode Six Sigma Dan Failure Mode Effect Analysis (FMEA) Di PT. Pesona Arnos Beton,” Jurnal Al-Azhar Indonesia Seri Sains dan Teknologi, vol. 8, no. 2, pp. 94–104, 2023.