Redesain Dies Proses Blank-Pierce dengan Penyesuaian Mesin Press Guna Meningkatkan Efisiensi Produk Reinforcement Quarter Panel Extension RH/L
Main Article Content
Abstract
The redesign of the die design in the blank-pierce process for the RH/LH quarter panel extension reinforcement product was carried out using field observations to obtain actual data. The production process consists of five stages: blanking, piercing, restriking, bending and forming. Meanwhile, in the redesign process, the RH/LH quarter panel extension reinforcement product is evaluated in the blanking and piercing die processes. Cycle time analysis after the tool design has been redesigned shows the potential for increasing efficiency by reducing process time. MPP data is used as a guide for die design with relevant machine specifications, die size and materials. Machine pressure and tonnage calculations were carried out for the current die design and the revised version, showing significant improvements in production efficiency. The die redesign was carried out to increase output per stroke and to use more sophisticated automation processes. The results of this research show that improved die design can increase production efficiency and productivity by reducing the number of strokes required and properly adjusting machine capacity.
Article Details
This work is licensed under a Creative Commons Attribution 4.0 International License.
References
E. Dosen, P. Studi, and T. Mesin, “Analisa Dimensi Blank Product Untuk Rear Bracket Cushion Sepeda Motor,” Presisi, vol. 22, no. 2, p. 49, 2020.
M. F. Nugroho, “Perhitungan Tonase Proses Stamping pada Cover Muffler NIKA di PT. XYZ,” Ilm. Tek. Mesin, vol. 03, no. 01, pp. 1–08, 2023, [Online]. Available: https://journal.unsika.ac.id/index.php/sigmat/index
Thomas Djunaedi, “Analisa Perhitungan Gaya - Gaya Mekanis Pada Pembuatan Komponen OtomotifBraket Upper Arm,” vol. 8, no. 2, pp. 1–6, 2014.
M. S. Alan, R. Hanifi, T. Mesin, and U. S. Karawang, “PERANCANGAN PENGUNCI SIDE GUIDE HOLDER PADA MESIN,” vol. 7, no. 2, pp. 100–105, 2022.
I. Suchy, Handbook of Die Design, 2nd Edition. New York: McGraw-Hill Education, 2006. [Online]. Available: https://www.accessengineeringlibrary.com/content/book/9780071462716
A. H. Fadillah, “Perancangan Jig and Fixture dengan Sistem Elektropneumatic,” 2022.
M. P. Groover, Fundamentals of Modern Manufacturing Material, Processes, and Systems, 5th Edition. 2013.
Falah Cepty Nur; Rispianda; Prassetyo Hendro, “Rancangan Combination Dies Untuk Produk Engine Mounting T120SS Di PT. Jati Wangi,” Reka Integr. J. Online Inst. Teknol. Nas., vol. 03, no. 03, pp. 380–391, 2015, [Online]. Available: https://ejurnal.itenas.ac.id/index.php/rekaintegra/article/view/900
A. Hilman, “Perancangan dan Analisis Stamping Dies untuk Pembuatan Produk Bracket Bumper Dengan Proses Press Multi Forging,” no. 100, pp. 1–20.
R. Riansyah and R. A. Darajatun, “Proses stamping press pembuatan Bracket Harness,” J. Ilm. Wahana Pendidik., vol. 8, no. 3, pp. 1–5, 2022, doi: 10.5281/zenodo.6301622.
N. Putri, A. R. Utary, and M. Nadir, “Analisis Manufacturing Cycle Effectiveness (Mce) Dalam Mengurangi Non Value Added Activities,” J. Manaj. FEB Univ. Mulawaraman, vol. 8, no. 2, pp. 167–180, 2016.
A. S. Fauziyyah and B. Purwanggono, “Analisis Kasus Overstock Dan Outstanding Material Menggunakan Root Causes Analysis (Studi Kasus: Pt Showa Indonesia …,” … Eng. Online J., pp. 1–8, 2018, [Online]. Available: https://ejournal3.undip.ac.id/index.php/ieoj/article/view/18279%0Ahttps://ejournal3.undip.ac.id/index.php/ieoj/article/download/18279/17358
D. Agustin, I. Syihab, Abdul Wahid Arohman, Edwin Sahrial Solih, and Fredy Sumasto, “Analisis Pengaruh Clearance terhadap Hasil Potong pada Proses Stamping Produk Member Floor Side Inner LH,” J. Serambi Eng., vol. 9, no. 1, pp. 7603–7608, 2023, doi: 10.32672/jse.v9i1.708.
D. Agustin, A. W. Arohman, M. Agus, H. Sudrajat, and S. Solihin, “Analisis Finite Element Aluminium Alloy 6063-T5 Pada Jig Positioning Untuk Perakitan Rooftop Interior Mobil,” J. Ilm. Univ. Batanghari Jambi, vol. 23, no. 2, p. 1231, 2023, doi: 10.33087/jiubj.v23i2.3654.
I. P. Mulyatno, A. Trimulyono, and S. F. Khristyson, “Analisa Kekuatan Konstruksi Internal Ramp Sistem Steel Wire Rope Pada Km. Dharma Kencana Viii Dengan Metode Elemen Hingga,” Kapal, vol. 11, no. 2, pp. 85–93, 2014.